PIC16F87T-E/ML【PDF 96/200 页】IC MCU FLASH 4KX14 EEPROM 28QFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3882

92页 93页 94页 95页 [96页]97页 98页 99页 100页

185

8008H–AVR–04/11

ATtiny48/88

19.1.1

EEPROM Write Prevents Writing to SPMCSR

Note that an EEPROM write operation will block all software programming to Flash. Reading the

Fuses and Lock bits from software will also be prevented during the EEPROM write operation. It

is recommended that the user checks the status bit (EEPE) in the EECR Register and verifies

that the bit is cleared before writing to the SPMCSR Register.

19.1.2

Reading the Fuse and Lock Bits from Software

It is possible to read both the Fuse and Lock bits from software. To read the Lock bits, load the

Z-pointer with 0x0001 and set the RFLB and SELFPRGEN bits in SPMCSR. When an LPM

instruction is executed within three CPU cycles after the RFLB and SELFPRGEN bits are set in

SPMCSR, the value of the Lock bits will be loaded in the destination register. The RFLB and

SELFPRGEN bits will auto-clear upon completion of reading the Lock bits or if no LPM instruc-

tion is executed within three CPU cycles or no SPM instruction is executed within four CPU

cycles. When RFLB and SELFPRGEN are cleared, LPM will work as described in the Instruction

set Manual.

The algorithm for reading the Fuse Low byte is similar to the one described above for reading

the Lock bits. To read the Fuse Low byte, load the Z-pointer with 0x0000 and set the RFLB and

SELFPRGEN bits in SPMCSR. When an LPM instruction is executed within three cycles after

the RFLB and SELFPRGEN bits are set in the SPMCSR, the value of the Fuse Low byte (FLB)

will be loaded in the destination register as shown below.See Table 20-5 on page 190 for a

detailed description and mapping of the Fuse Low byte.

Similarly, when reading the Fuse High byte (FHB), load 0x0003 in the Z-pointer. When an LPM

instruction is executed within three cycles after the RFLB and SELFPRGEN bits are set in the

SPMCSR, the value of the Fuse High byte will be loaded in the destination register as shown

below. See Table 20-4 on page 189 for detailed description and mapping of the Fuse High byte.

Fuse Extended byte can be read by loading the Z-pointer with 0x0002. When an LPM instruction

is executed within three cycles after the RFLB and SPMEN bits are set in the SPMCSR, the

value of the Fuse Extended Byte (FEB) will be loaded in the destination register as shown

below. See Table 20-3 on page 189 for detailed description and mapping of the Fuse Extended

byte.

Fuse and Lock bits that are programmed, will be read as zero. Fuse and Lock bits that are

unprogrammed, will be read as one.

Bit

76543210

––––––

LB2

LB1

Bit

321

FLB7

FLB6

FLB5

FLB4

FLB3

FLB2

FLB1

FLB0

Bit

765

321

FHB7

FHB6

FHB5

FHB4

FHB3

FHB2

FHB1

FHB0

Bit

321

FEB7

FEB6

FEB5

FEB4

FEB3

FEB2

FEB1

FEB0

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式